1998 vani 6.5td, startille asti ei tuu virtalukolta sähköö??
1998 vani 6.5td, startille asti ei tuu virtalukolta sähköö??
sukulaisen vani teki tempun ja jäi pihaan. eli avaimesta kun vääntää niin konehuoneessa naksahtaa sulakerasiassa rele, mutta kävin alla virtakynällä koittamas että startille asti sähköö ei tule. ruuvarin kun tuuppaa solenoidin napojen väliin niin pyörittää kyllä. neutral switchiä ite epäilin ja koitin vaihteitakin vähän renkuttaa samalla kun pidin avainta starttiasennossa: ei vaikutusta. virtalukko tos on vähän takerrellut eli aina ei meinaa kääntyä ellei ota avaimia kerran pois ja laita takaisin ( kääntää avaimen tai välis ei tarvii kääntääkkään) itellä ei näitä "uudempia" vaneja ole ollut, ni täältä kysynkin että onko näihin vaihdeltu paljon virtalukkoja tai noita neutral switchejä, vai mistä mä alan vikaa hakemaan???
Re: 1998 vani 6.5td, startille asti ei tuu virtalukolta sähk
Käynnistyksen esto päällä?
GM Tech 2
Snap-On MT-2500
AE+GMTD Scan tech
OBD2 Lastutukset kaikkiin merkkeihin.
https://www.facebook.com/Dtech.fi
Snap-On MT-2500
AE+GMTD Scan tech
OBD2 Lastutukset kaikkiin merkkeihin.
https://www.facebook.com/Dtech.fi
Re: 1998 vani 6.5td, startille asti ei tuu virtalukolta sähk
Jos startin rele toimii, jännite tulee virtalukolta releelle. Releeltä sen tulee jatkaa startin navalle S. Akkujännite tulee myös navalle B, koska startti pyörii solenoidin navat yhteen kytkiessä. Starttimoottori on myös tällöin kunnossa. Vika on todennäköisesti releen ja startin välisessä violetissa johdossa tai sen liittimissä. Oheisena englanninkielinen selostus käynnistysjärjestelmän virrankierrosta. Kytkentäkaavionkin laittaiisin, mutta en osaa sitä vielä tehdä.
Document ID# 200844
1998 Chevrolet/Geo Express
--------------------------------------------------------------------------------
Starting System Operation
Starter Circuit Operation
Battery voltage is available at the Ignition Switch and the Starter Relay contacts at all times through the RED (242) wire from the IGN-A fuse in the Underhood Fuse-Relay Center. Placing the Ignition Switch in START closes contacts to apply voltage on the YEL (5) wire to the Park/Neutral Position Switch. If the Automatic Transmission is in either Park or Neutral, voltage is applied from the YEL (1737) wire to the Starter Relay coil. The Starter Relay coil is grounded at Ground G103 by the BLK (150) wire. With voltage applied to the coil, the Starter Relay energizes. Voltage is then applied to the Starter Solenoid Winding Terminal S through the PPL (6) wire. Battery voltage is also available at all times through the BLK (1) wire at Starter Solenoid Terminal B. With battery voltage applied at Starter Solenoid Terminal S, current flows though the Hold-In Winding to the mechanical ground at the solenoid. Simultaneously, current flows through the Pull-In Winding and the Starter Motor to the Starter Motor's mechanical ground. The combined force of these windings overcomes the force of the Return Spring and pulls the starter's Plunger to engage the starter with the Flywheel Drive Assembly though the Shift Lever. The engine starts to turn over. The Plunger actuation also operates a contact in the Starter Solenoid which closes to apply battery voltage directly to the Starter Motor. With battery voltage applied directly to the Starter Motor, the Pull-In Winding no longer has a voltage drop across the coil and current ceases to flow. The Starter Solenoid remains engaged due to the current flow through the Hold-In Winding alone. The Starter motor continues to operate until the Ignition Switch is returned to the RUN position. With the Ignition Switch now in the RUN position, voltage is removed from Starter Solenoid Terminal S. However, voltage is still present at Terminal B. Both the Hold-In Winding and the Pull-In Winding are energized by battery voltage from the BLK (1) wire. However, the forces from these windings now oppose one another and the Plunger returns to the disengaged position through the operation of the Return Spring. This operates the contact to remove battery voltage from the Starter Motor and the motor stops. Both windings also de-energize. This Plunger operation also retracts the starter from the Flywheel Drive Assembly and the engine operates on its own power.
--------------------------------------------------------------------------------
Document ID# 200844
1998 Chevrolet/Geo Express
--------------------------------------------------------------------------------
Starting System Operation
Starter Circuit Operation
Battery voltage is available at the Ignition Switch and the Starter Relay contacts at all times through the RED (242) wire from the IGN-A fuse in the Underhood Fuse-Relay Center. Placing the Ignition Switch in START closes contacts to apply voltage on the YEL (5) wire to the Park/Neutral Position Switch. If the Automatic Transmission is in either Park or Neutral, voltage is applied from the YEL (1737) wire to the Starter Relay coil. The Starter Relay coil is grounded at Ground G103 by the BLK (150) wire. With voltage applied to the coil, the Starter Relay energizes. Voltage is then applied to the Starter Solenoid Winding Terminal S through the PPL (6) wire. Battery voltage is also available at all times through the BLK (1) wire at Starter Solenoid Terminal B. With battery voltage applied at Starter Solenoid Terminal S, current flows though the Hold-In Winding to the mechanical ground at the solenoid. Simultaneously, current flows through the Pull-In Winding and the Starter Motor to the Starter Motor's mechanical ground. The combined force of these windings overcomes the force of the Return Spring and pulls the starter's Plunger to engage the starter with the Flywheel Drive Assembly though the Shift Lever. The engine starts to turn over. The Plunger actuation also operates a contact in the Starter Solenoid which closes to apply battery voltage directly to the Starter Motor. With battery voltage applied directly to the Starter Motor, the Pull-In Winding no longer has a voltage drop across the coil and current ceases to flow. The Starter Solenoid remains engaged due to the current flow through the Hold-In Winding alone. The Starter motor continues to operate until the Ignition Switch is returned to the RUN position. With the Ignition Switch now in the RUN position, voltage is removed from Starter Solenoid Terminal S. However, voltage is still present at Terminal B. Both the Hold-In Winding and the Pull-In Winding are energized by battery voltage from the BLK (1) wire. However, the forces from these windings now oppose one another and the Plunger returns to the disengaged position through the operation of the Return Spring. This operates the contact to remove battery voltage from the Starter Motor and the motor stops. Both windings also de-energize. This Plunger operation also retracts the starter from the Flywheel Drive Assembly and the engine operates on its own power.
--------------------------------------------------------------------------------